Aeon Labs Doorbell is a switch binary device based on Z-wave enhanced slave library V6.51.06.
The Doorbell supports playing MP3 music files with a press of this doorbell. It has a 16MB flash memory that can store up to 100 ringtones. The volume can be adjusted manually via short press on the Volume Button, also you can switch the doorbell sound to the next via long press on the Volume Button. You may change/update your doorbell ringtone at any point in time you want by connecting your Doorbell to your PC to update the sound track on your Doorbell’s flash memory.
1. Install Doorbell, and plug it into the socket of AC Power.
2. Let the primary controller into inclusion mode (If you don’t know how to do this, please refer to its manual).
3. Press the Action Button.
4. If the inclusion is failed, please repeat the process from step 2.
1. Install Doorbell, and plug it into the socket of AC Power.
2. Let the primary controller into exclusion mode (If you don’t know how to do this, refer to its manual).
3. Press the Action Button.
4. If the remove is failed, please repeat the process from step 2.
Note: If Doorbell is removed from Z-wave network, it will be reset to factory default.
]]>Value=1 to 255, the range of repetition is 1 to 100. Value =0, ignore. Note: If the time of playing doorbell ringtone is more than 20s, the volume of ringtone will reduce to silence no matter how many repetitions of doorbell ringtone are set.
]]>0: button- is previous, button+ is next
1: button- is next, button+ is previous
]]>0: short pressing changes volume, long pressing changes
default ringtone.
1: long pressing changes volume, short pressing changes
default ringtone.
0x00: normal battery level
0xff: low battery level
set 0x00: cancel low battery alert
]]>Enable/disable to send notifications to associated devices (Group 1) when the state of Doorbell is changed (0=nothing, 1=hail CC, 2=basic CC report)
]]>Enable/disable to send notifications to associated devices (Group
1) when the Wireless Button’s battery is in low battery state
(0=nothing, 1=Configuration report 0x2A)
Pair the Wireless Button with Doorbell.
Value=0x55555555, Start the Wireless Button pairing mode and
the blue Led will blink slowly, short press the Wireless Button
once, if the blue Led change to be solid, which means the pairing
is successful. Otherwise, repeat the steps.
It will automatically exit the pairing mode after 8s if there is no
pressing action of the Wireless Button.
Note:
You can send this configuration Get CC to ask the pairing result:
If configuration report value=0x00000000, which means the
pairing is failed.
If configuration report value =0xFFFFFFFF, which means the
pairing is successful.
0: config not locked
1: config locked
]]>1. Size=0x01, Configuration Value=0x00:
Reset configuration setting.
2. Size=0x04, Configuration Value=0x55555555:
Reset Factory setting.
Set this to any ringtone (1-100) to have it play that ringtone.
]]>Control items: Value=1, play Value=2, stop Value=3, pause Value=4, Next Value=5, Previous Other, ignore
]]>When the state of Doorbell (trigger to turn on/off the rington
e ) is changed:
1, Set Configuration parameter 80 to 0: Reserved (Default).
2, Set Configuration parameter 80 to 1: Send Hail CC.
3. Set Configuration parameter 80 to 2: Send the Basic
Report.
Forward the Basic Set, Switch Binary Set, Switch Multilevel
Start Level Change, Switch Multilevel Stop Level Change,
Switch Multilevel Set, Scene Activation Set to associated
nodes in Group 2 when the Doorbell receives the Basic Set,
Switch Binary Set, Switch Multilevel Start Level Change,
Switch Multilevel Stop Level Change, Switch Multilevel Set,
Scene Activation Set commands from main controller.